GRASS logo

Note: This addon document is for an older version of GRASS GIS that will be discontinued soon. You should upgrade your GRASS GIS installation, and read the current addon manual page.

NAME

r.massmov - Estimates run-out and deposition of landslide phenomena over a complex topography.

KEYWORDS

raster, landslide, model

SYNOPSIS

r.massmov
r.massmov --help
r.massmov [-im] elev=string h_ini=string fluiddist=string rheology=string [rho=float] [ystress=float] [visco=float] [chezy=float] [bfrict=float] ifrict=float fluid=float timesteps=integer [deltatime=integer] [stop_thres=float] [step_thres=integer] [threads=integer] [h=string] [h_max=string] [v=string] [v_max=string] [--overwrite] [--help] [--verbose] [--quiet] [--ui]

Flags:

-i
Print input data
-m
Print memory usage requirements
--overwrite
Allow output files to overwrite existing files
--help
Print usage summary
--verbose
Verbose module output
--quiet
Quiet module output
--ui
Force launching GUI dialog

Parameters:

elev=string [required]
Name of elevation raster map
h_ini=string [required]
Name of landslide initial body thickness raster map
fluiddist=string [required]
Name of distance from the landlide toe raster map
rheology=string [required]
Name of rheological law
Options: frictional, Voellmy, viscoplastic
rho=float
Density of the flow [Kg/m3]. Required only for viscous rheologies.
ystress=float
Apparent yield stress [Pa]. Used only for viscous rheologies (optional).
visco=float
Dynamic viscosity [Pa*s]. Required only for viscous rheologies
chezy=float
Chezy roughness coefficient [m/s2]. Required only for Voellmy rheology
bfrict=float
Angle of basal friction [deg]
ifrict=float [required]
Angle of internal friction [deg]
fluid=float [required]
Upward velocity of transition from solid to fluid of the landsliding mass [m/s]
timesteps=integer [required]
Maximum number of time steps of the simulation [s]
deltatime=integer
Reporting time frequency [s]
stop_thres=float
Pearson value threshold for simulation stop [-]
step_thres=integer
Number of time steps for evaluating stop_thres value [-]
threads=integer
Number of threads for parallel computing
h=string
Prefix for flow thickness output raster maps
h_max=string
Prefix for maximum flow thickness output raster maps
v=string
Prefix for flow velocity output raster maps
v_max=string
Prefix for maximum flow velocity output raster maps

Table of contents

DESCRIPTION

r.massmov is a numerical model that allows users to simulate the expansion (runout) and deposition of mass movements over a complex topography by approximating the heterogeneous sliding mass to a homogeneous one-phase fluid (following the approach proposed by Savage and Hutter (1989) and Iverson and Denlinger (2001)). The model describes the mass movements as a two-dimensional flux taking advantage of the shallow water equations. This formula is derived from the general Navier-Stokes equations under the hypothesis that the vertical components of velocity and pressure are negligible with respect to the horizontal components, and that the vertical pressure profile can be considered as almost hydrostatic (Kinnmark 1985).

The required inputs can be classified in three categories based on the information type:

The model outputs a series of flux velocity map (v) and deposit depth raster map (h) at different time step according to the set deltatime parameter; additionally the module outputs two raster maps representing the maximum thickness (h_max) and velocity (v_max) registered during the simulation.

NOTES

The generation of the model input maps, in case the simulation refer to en existing collapse and pre and post event DTM is available, can be performed taking advantage of the GRASS modules; in particular:

DIAGNOSTICS

The module has been tested in several cases (see references), but up to now most of the simulations was done using a Voellmy rheology thus other rheology laws should be better investigated.

REFERENCES

Begueria S, Van Asch T W J, Malet J P and Grondahl S 2009 A GIS based numerical model for simulating the kinematics of mud and debris flows over complex terrain. Nat Hazards Earth Syst Sci, 9, 1897-1909.

Iverson R M and Denlinger R P 2001 Flow of variably fluidized granular masses across threedimensional terrain: 1, Coulomb mixture theory. Journal of Geophysical Research 106:537-52

Kinnmark I P E 1985 The shallow water equations: Formulation, analysis and application. In Brebia C A and Orszag S A (eds) Lecture Notes in Engineering 15. Berlin, Springer-Verlag:1-187

Molinari M, Cannata M, Begueria S and Ambrosi C 2012 GIS-based Calibration of MassMov2D. Transactions in GIS, 2012, 16(2):215-231

Savage S B and Hutter K 1989 The motion of a finite mass of granular material down a rough incline. Journal of Fluid Mechanics 199:177-215

SEE ALSO

r.grow.distance
r.slope.aspect
r.mapcalc

AUTHORS

Original version of program:
Santiago Begueria

The current version of the program (ported to GRASS7.0):
Monia Molinari, Massimiliano Cannata, Santiago Begueria.

SOURCE CODE

Available at: r.massmov source code (history)

Latest change: Mon Jun 28 07:54:09 2021 in commit: 1cfc0af029a35a5d6c7dae5ca7204d0eb85dbc55


Note: This addon document is for an older version of GRASS GIS that will be discontinued soon. You should upgrade your GRASS GIS installation, and read the current addon manual page.

Main index | Raster index | Topics index | Keywords index | Graphical index | Full index

© 2003-2023 GRASS Development Team, GRASS GIS 7.8.8dev Reference Manual